Beko DCU7230W Condenser Tumble Dryer Not Working & Responding
Hi,Beko DCU7230W condenser tumble dryer was working without any noticeable problems. Turned on to use this weekend and nothing happens - no lights, nothing. Have checked all usual power problems - fuse OK, not tripped etc. There is 240V going into the machine... took the front off and have looked at the PCB. There is a small burn mark on the plastic and the component underneath is blistered on its surface. Not sure if this would cause the problem - or symptomatic. Also not sure if repairable or need to splurge for PCB - very aware that if symptomatic rather than causal I could quickly blow £70 if another PCB then suffers same fate. Have put a couple of photos and brief video in Dropbox. Link below.Thank you!!! Best wishesEuan
I will try and help with this problem about Beko DCU7230W Condenser Tumble Dryer,
Thanks for sending your photos:

Beko DCU7230W Condenser Tumble Dryer PCB1

Beko DCU7230W Condenser Tumble Dryer PCB2
Hi Euan,
Thanks a lot for the detailed pictures and the video. Let's start with the circuit board. In the top left corner of one photo, you'll see a relay surrounded by some capacitors and a blue item, which I think is part of a filtering system. Next to that, there's a resistor that looks like it's blown. These resistors are replaceable and not too expensive, usually less than a couple of pounds. You'll need to use the colour identification scheme to determine the resistor size.
What worries me is the other side of the circuit board. Look at U4; there's a large chip on the left with multiple contacts. To its right, you'll see another chip with two or three legs, also marked U4 on the board. It looks like it might be bulging. The photo didn't capture it well, but it seems like it may have failed, making replacement trickier.
We have a few options. I understand the cost concerns about replacing the circuit board only for it to fail again. But I'd hate for this tumble dryer to end up in landfill over something as simple as a circuit board.
I've gathered the workshop manual, wiring diagram, exploded diagrams, and a full list of genuine part numbers for you. While we may not sell the circuit board and I'm currently in Germany so can't check my UK warehouse for second-hand ones, I can suggest some ways to find one.
First, use your model number (ignore the 'W' at the end of DCU7230W as it stands for white). Check eBay for second-hand machines with heating problems or other issues; you could salvage parts from these machines or vice versa.
Alternatively, use your model number or genuine part number to search on Amazon, Gumtree, Facebook Marketplace, and eBay. Sometimes engineers sell old stock cheaply; you might find a circuit board for £20-£30 if you're lucky.
I spent some time putting this together for you while enjoying a leisurely Sunday afternoon by a canal in Germany with a few beers. I hope this helps and gives you inspiration to recycle this machine into a fully functional one again.
Good luck with your repair! Sorry I can't give you a one-to-one call as I'm at a conference in Germany. IFA Berlin
If you want to support the site please mark us to your favourites, also I would be grateful if you would subscribe to our social media channels as this really helps my site and keeps us going.
YouTube. http://www.youtube.com/user/howtorepair
Facebook. https://www.facebook.com/how.to.repair.appliances
And if we really helped you save money you can always click on the Buy Paul a Beer page

Beko DCU7230W Condenser Tumble Dryer Spares
Match your part for Beko DCU7230W Condenser Tumble Dryer and the use reference number in list below and click on the link to your part
Beko DCU7230W Condenser Tumble Dryer Wiring Diagram
Beko DCU7230W Condenser Tumble Dryer Wiring Diagram 2
Beko DCU7230W Condenser Tumble Dryer Service Manual
Beko DCU7230W Condenser Tumble Dryer Instruction Manual
Beko DCU7230W Condenser Tumble Dryer Service Test Program
Beko DCU7230W Condenser Tumble Dryer Error Flow
Beko DCU7230W Condenser Tumble Dryer Front Door Assembly
Beko DCU7230W Condenser Tumble Dryer Main Body Assembly
full list of spare parts for Beko DCU7230W Condenser Tumble Dryer model below
| Reference | Part Number | Description |
|---|---|---|
| 1 | 2963930100 | TOP PLATE |
| 10 | 2976900100 | FRONT DOOR ASSEMBLY |
| 1003 | 2971650200 | CAPACITOR (ARCOTRONICS 8 uF) |
| 1005 | 2962510800 | CONDENS PUMP |
| 1005 | 2962510600 End Of Life | CONDENS PUMP |
| 1044 | 133000001 | WASHER 12x18x1 DIN 988.. |
| 1045 | 160200200 | Snap Ring 9x1 DIN 6799 DRCS68 |
| 1046 | 2973902900 | REAR PANEL ASSY |
| 1087 | 2982820100 | HOSE AND CABLE HOLDER OPPOSITE DIRECTION |
| 1098 | 2962630100 | FAN COVER - COOLING |
| 12 | 2962120100 | INNER DOOR_(ARES_ARC1_WITHOUT_SWITCH) |
| 1209 | 2969500300 | LOCK BODY ASS |
| 1211 | 2963910100 | LIGHT GUIDE |
| 1244 | 2979290100 | POMP COVER |
| 1246 | 2971703502 | CABLE ASSEMBLY |
| 1248 | 2960910300 | SILICONE GASKET |
| 1249 | 2980703800 | CABLE ASSEMBLY |
| 1256 | 2973100100 | SHAFT-FRONT BEARING ASSY |
| 1259 | 2972300100 | FILTRE CASETTE ASSY |
| 1260 | 2962960100 | OVERFLOW FLOAT |
| 1268 | 2963670100 | LIGHT GUIDE SET |
| 1271 | 2970020300 | AIR GUIDING PART |
| 1279 | 2968300300 | BEARING SENSOR COVER ASSEMBLY |
| 1287 | 2960150100 | RUBBER STOPPER |
| 1290 | 2962590100 | DOOR GASKET |
| 1295 | 2963120100 | MOTOR BRACKET CLAMP (PLASTIC) |
| 1303 | 2963830100 | TANK GUIDE (TOP_54CM) |
| 1306 | 2961390300 | TANK GUIDE BARRIER |
| 1313 | 2705810300 | PT SCREW (3_5x8) |
| 1377 | 2965200600 | MAIN CABLE ASSEMBLY |
| 1390 | 9002900200 | COUNTERSUNK HEAD SCREW (PT-4X14) |
| 1391 | 2951610300 | DELTA PT SCREW(5x20 TORX HEAD_PERFOR.) |
| 1398 | 2951780300 | DELTA PT VIDA 50x26 WN 5454 HB |
| 1399 | 2962950100 | NTC GASKET |
| 14 | 2962170200 | HINGE |
| 1401 | 2963210100 | MOTOR SHAFT SEAL |
| 1417 | 2705810400 | PT SCREW (3_5x14) |
| 1440 | 2983410100 | PLASTIC FOOT ASSY (2K) |
| 1440 | 2961690100 | ADJUSTABLE PLASTIC FOOT |
| 1451 | 2963180200 | BACK COVER FELT |
| 1453 | 2953741500 | SINGLE ADHESINE EPDM FOAM |
| 1454 | 2963090200 | AIR GUIDING GASKET |
| 1455 | 2962810100 | SIDE WALL PIN |
| 1457 | 2971900300 | NTC (THINKING_12K) |
| 1457 | 2971900200 | NTC (EPCOS_12K) |
| 1457 | 2971900500 | NTC (GAOLI_12K) |
| 1457 | 2971900100 | NTC |
| 1459 | 2969900200 End Of Life | ROLLER ASSY |
| 1460 | 2951261000 | POMP WATER TANK HOSE. |
| 1460 | 2951261200 | POMP WATER TANK HOSE. |
| 1461 | 2962850500 | DRUM LIFTER |
| 1462 | 2951260800 | POMP WATER TANK HOSE. |
| 1465 | 2951261100 | POMP WATER TANK HOSE. |
| 1466 | 9003272000 | PLASTIC SCREW (DIAMETER 4x10) INOX |
| 1469 | 100700120 | SCREW (B4.2*9.5 DIN 7982-H) |
| 1471 | 2953741100 | SINGLE ADHESINE EPDM FOAM. |
| 1473 | 2962390100 | LOCK MOUTH |
| 1474 | 2960720100 | TIME DELAY PCB |
| 1475 | 2960304600 | CABLE ASSEMBLY |
| 1478 | 2963420100 | WATER COLLECTOR |
| 1481 | 2963950200 | COLD AIR ROUTER |
| 1483 | 2963250100 | COOLING AIR OUTFLOW FELT |
| 1484 | 2963590100 | YAN DESTEK (SAG-54CM) |
| 1485 | 2963610100 | SIDE SUPPORT (LEFT) |
| 1486 | 2974470300 | SHAFT DRUM COVER |
| 1486 | 2974470100 | SHAFT DRUM COVER |
| 1486 | 2974470700 | SHAFT DRUM COVER SHC ALS |
| 1489 | 2962290100 | DOWN HINGE GUIDE |
| 1490 | 2962310100 | UP HINGE GUIDE |
| 1492 | 2962460100 | TANK GUIDE CAP |
| 1493 | 2826510200 | PEG PLASTIC CLAMP |
| 1495 | 9003271700 | PLASTIC SCREW |
| 1517 | 2953741400 | SINGLE ADHESINE EPDM FOAM |
| 1587 | 2966990100 | CABLE TRAY |
| 166 | 2994900700 | MAIN CABLE ASSEMBLY |
| 169 | 2970447100 | POWER SUPPLY CORD |
| 169 | 2970445400 | POWER SUPPLY CORD |
| 169 | 2970444900 | POWER SUPPLY CORD |
| 180 | 2964170100 | ON_OFF SWITCH(ROLD (+) FORM) |
| 186 | 2970012102 | ELECTRONIC PCB ASSY. (CNDU SENS_3K) |
| 189 | 491500303 | POLY-V 285 H 4 MA BELT |
| 197 | 2963749016 | DRAWER PANEL ASS. |
| 200 | 2976109011 | PANEL BODY |
| 2013 | 2970540100 | POWER PLUG HOLDER |
| 203 | 2976702000 | PROGRAMME KNOB BUTTOM_ASSY |
| 2071 | 2972960100 | DUAL SOCKET COVER |
| 2072 | 2972950100 | DUAL SOCKET CASING COVER |
| 208 | 2963989010 | PANEL BODY |
| 300 | 2963680100 | FUUNCTION BUTTON |
| 33 | 9001230800 | PLASTIC CLAMP 152 mm |
| 339 | 2963640100 | OUTER DOOR |
| 341 | 2962150100 | LOCK HOOK |
| 374 | 265900012 End Of Life | OVEN LAMP 15 W-230 V |
| 401 | 2963580100 | FRONT PANEL |
| 402 | 2965080100 | FIXER |
| 412 | 100601820 | SCREW (B4.2x16 DIN 7981-H) |
| 4210 | 2974870100 | INTERFERENCE FILTER |
| 43 | 2960310464 | USER'S MANUAL. |
| 468 | 2963710100 | ON OFF BUTTON (TIP02+ARC 734 MAVI) |
| 48 | 2985425900 | DRUM ASSEMBLY |
| 481 | 2827190400 | Rotary switch |
| 581 | 2966980100 | HEATER CABLE GUARD |
| 583 | 2705870100 | SELF LOCKING CABLE HOLDER |
| 59 | 2962470200 | ELASTIC POLY-V BELT. 7PH 1956 |
| 63 | 2971420100 End Of Life | Dryer Motor Group WELLING |
| 63 | 2968590100 End Of Life | Dryer Motor WELLING |
| 632 | 2962160100 | HINGE BUSHING |
| 65 | 2970101500 | HEATER ASSY |
| 685 | 2963690100 | TIME ADJUSTMENT BUTTON |
| 750 | 2961850100 | PCB HOLDER |
| 804 | 2973801100 | REAR DRUM TIGHTNESS PLATE ASSY |
| 804 | 2973800700 | REAR DRUM TIGHTNESS PLATE ASSY |
| 804 | 2973800100 | REAR DRUM TIGHTNESS PLATE ASSY |
| 822 | 2963540100 | KICK PLATE - LEFT |
| 826 | 2972900800 | HEATER COVER ASSY |
| 826 | 2972900500 | HEATER COVER ASSY |
| 827 | 2962020100 | UPPER BEAM |
| 8303 | 9003270200 | PLASTIC SCREW |
| 8318 | 2002370900 | HOSE CLAMP (Ø 16.4) |
| 8320 | 100601520 | SHEET METAL SCREW (B4.2X13 DIN 7981-H) |
| 834 | 2959400200 | REAR BEARING ASSEMBLY |
| 8384 | 9003270100 | PLASTIC SCREW |
| 8385 | 9003270400 | PLASTIC SCREW (4_10) |
| 8386 | 9003270500 | PLASTIC SCREW (4_12) |
| 8388 | 2966700200 | SUPPORT PART OF SHEET TOP PLATE ASSY. |
| 8392 | 9003610300 | sheet metal screw(B4_2x9_5-perforated) |
| 8397 | 9003610100 | SHEET METAL SCREW(B4_2x9_5-perforated) |
| 8403 | 9003860300 | SHEET METAL SCREW |
| 8413 | 120800120 | FIBERED_NUT_M6X1_DIN_985 |
| 8419 | 2963340100 End Of Life | WASHERED NUT (M6x1) |
| 842 | 2960190100 | CABLE HOLDER |
| 8422 | 2951580400 | COUNTERSUNK HEAD PT SCREW (4.5x12) |
| 8428 | 2971870100 | MX10 RYSB PERFORATED SCREW |
| 843 | 2963820100 | WATER TANK (UP_7KG_54CM) |
| 8430 | 9003860900 | SHEET METAL SCREW |
| 8434 | 2951780400 | DELTA PT SCREW |
| 844 | 2961290200 | DISCHARGING FUNNEL |
| 845 | 2963530100 | KICK PLATE - RIGHT |
| 846 | 2962680100 | CONDENSER SNAPPER |
| 847 | 2975700100 | PLASTIC CHASIS ASSY |
| 856 | 2974940100 | HINGE PIN HOLDER (PLASTIC) |
| 857 | 2963150300 | SPRING |
| 861 | 2963330400 | FRONT SELING FELT |
| 865 | 2962650100 | LAMP COVER |
| 873 | 2963230100 | PCB HOLDER COVER |
| 877 | 2962930200 | PROCESS FAN |
| 888 | 2951061000 | MICRO_SWITCH |
| 888 | 2951060600 | MICRO SWITCH |
| 888 | 2951060700 | MICRO_SWITCH |
| 891 | 2961680100 | COOLING FAN |
| 9 | 2963650100 | HANDLE |
| 906 | 2961190200 | SPECİAL WASHER (8,1*17*1,5) |
| 921 | 2980000200 | CONDENDER ASSY. (54CM) |
| 921 | 2980000300 | CONDENDER ASSY. (54CM) |
| 932 | 2961961100 | SIDE PANEL |
| 985 | 2954700400 | Micro Switch Ass. |
| 985 | 2954700100 End Of Life | Micro Switch Ass. |
Service Documents
Parts for This Model
Showing compatible parts for model DCU7230W